Indoor solid fuel use for heating and cooking with blood pressure and hypertension: A cross-sectional study among middle-aged and older adults in China

A cross-sectional study was conducted to investigate the impact of solid fuel use for heating and cooking on blood pressure (BP) and hypertension, using data from the China Health and Retirement Longitudinal Study (CHARLS). The primary fuels used for indoor heating and cooking were collected by questionnaires, respectively. Hypertension was defined based on self-report of physician's diagnosis, and/or measured BP, and/or anti-hypertensive medication use. Multivariate logistic regression models were constructed to assess the associations. Among 10 450 eligible participants, 68.2% and 57.2% used indoor solid fuel for heating and cooking, respectively. Compared with none/clean fuel users, solid fuel for heating was associated with elevated BP (adjusted β: 2.02, 95% CI: 1.04–3.01 for systolic BP; adjusted β: 1.36, 95% CI: 0.78–1.94 for diastolic BP) and increased risk of hypertension (adjusted odds ratio: 1.15, 95% CI: 1.03–1.29). The impact of indoor solid fuel for heating on BP was more evident in rural and north residents, and hypertensive patients. We did not detect any significant associations between solid fuel use for cooking and BP/hypertension. Indoor solid fuel use is prevalent in China, especially in the rural areas. Its negative impact on BP suggested that modernization of household fuel use may help to reduce the burden of hypertension in China.     

Preparation and characterization of calcium phosphate cement with enhanced tissue adhesion for bone defect repair

Anti-washout and tissue adhesion properties are essential for the clinical application of injectable bone materials. In this study, we prepared calcium phosphate cement (CPC) with anti-washout and tissue adhesion properties and attempted to build covalent bonds between CPC and the amino groups in bone tissue under a self-regulating pH system in the CPC (acidic to basic). The results of push-out tests demonstrated that a significant enhancement (from 6.42 ± 0.76 N to 61.5 ± 4.09 N) in tissue adhesion was obtained with the addition of 6% (w/w) oxidized sodium alginate (OSA) in CPC. The FTIR, XRD, anti-washout test, XPS, pH test, and SEM results suggested that the synergistic effect of OSA-citric acid (CA) led to the formation of a three-dimensional gel network structure in the CPC, and the Schiff base reaction between aldehyde and amino groups induced adhesion between CPC and the bone tissue. Further, the addition of less OSA had no significant negative effect on the hydration properties of CPC. Our work aims to promote the development of injectable bone material in clinical applications.     

高光谱激光雷达谱位合一的角度效应分析

高光谱激光雷达以其谱位合一的技术优势为实现超三维精准遥感观测提供了可行途径,因此成为当前激光雷达与高光谱遥感领域共同大力推进的前沿发展方向。目前已有多型原型系统研发出来并得到了原理性验证,然而针对其数据处理核心环节问题的基础技术仍较为欠缺。典型问题之一是不同波段回波信号受激光入射角度的影响,该角度效应限制了高光谱激光雷达实现高性能遥感。以芬兰空间信息研究所高光谱激光雷达原型系统扫描桦树树干为例探讨了该角度效应,发现了不同激光波段对不同入射角度的回波强度响应模式,推导出了角度效应的基本规律及其精细尺度的统计规律,为后续该方向的系统研发、数据处理及信息提取等提供了可借鉴的底层机理与技术基础。     

Stream-Based Data Sampling Mechanism for Process Object

Process object is the instance of process. Vertexes and edges are in the graph of process object. There are different types of the object itself and the associations between object. For the large-scale data, there are many changes reflected. Recently, how to find appropriate real-time data for process object becomes a hot research topic. Data sampling is a kind of finding c hanges o f p rocess o bjects. There i s r equirements f or s ampling to be adaptive to underlying distribution of data stream. In this paper, we have proposed a adaptive data sampling mechanism to find a ppropriate d ata t o m odeling. F irst o f all, we use concept drift to make the partition of the life cycle of process object. Then, entity community detection is proposed to find changes. Finally, we propose stream-based real-time optimization of data sampling. Contributions of this paper are concept drift, community detection, and stream-based real-time computing. Experiments show the effectiveness and feasibility of our proposed adaptive data sampling mechanism for process object.     

Screening of frozen-thawed conditions for keeping nutritive compositions and physicochemical characteristics of goat milk

Frozen milk can help producers overcome the seasonality of goat milk production, low goat production and short lactation periods, and avoid discarding milk during some special periods. We investigated effects of combination between freezing (cryogenic refrigerator of ?16 to ?20°C or ultra-cryogenic refrigerator of ?76 to ?80°C) and thawing (homeothermy of 20 to 25°C or refrigeration of 2 to 4°C) on nutritive compositions and physicochemical characteristics of raw goat milk during storage period (80 d). Compared with fresh goat milk, the frozen-thawed milk decreased contents of fat, protein, and lactose, as well as surface tension and stability coefficient, whereas increased effective diameter and polydispersity index. The average values of color values (L*, a*, and b*) in 4 group samples changed from 83.01 to 82.25, ?1.40 to ?1.54, 3.51 to 3.81, respectively, and the ΔE of most samples did not exceed 2. In contrast to the other 3 frozen-thawed treatments, goat milk treated with ultra-cryogenic freezing-homeothermic thawing (UFHT) possessed higher fat (5.20 g/100 g), smaller effective particle diameter (0.32 µm), and the lowest polydispersity index value (0.26). The color and confocal laser scanning microscopy images of UFHT were similar to those of fresh goat milk, illustrating UFHT was the optimal approach to maintain the natural quality of goat milk. Our finding provides a theoretical basis for producers to freeze surplus milk.     

DNAN及TNT基熔铸炸药综合性能比较

为了对比载体炸药2,4,6-三硝基甲苯(TNT)和2,4-二硝基苯甲醚(DNAN)、以及以它们为基的熔铸炸药的综合性能,系统研究了DNAN和TNT、以及DNAN/HMX(20/80)和TNT/HMX(25/75)熔铸炸药的流变、能量、安全、以及力学等性能。结果表明:载体炸药DNAN(6.87 m Pa·s)的粘度低于TNT(9.05 mPa·s),DNAN/HMX熔铸体系的极限固含量(约80%)高于TNT/HMX熔铸体系(约75%);DNAN/HMX(20/80)和TNT/HMX(25/75)熔铸炸药的爆速分别为8336 m·s~(-1)和8452 m·s~(-1),爆压分别为31.03 GPa和31.44 GPa;在1 K·min~(-1)的慢速烤燃条件下,DNAN/HMX(20/80)和TNT/HMX(25/75)熔铸炸药的响应等级分别为燃烧反应和爆炸反应;在4.51GPa的冲击波入射压力条件下,TNT/HMX(25/75)在8～12 mm内达到完全爆轰,而DNAN/HMX(20/80)在12 mm内未能达到完全爆轰;DNAN/HMX(20/80)的抗拉和抗压强度均大于TNT/HMX(25/75)。因此可以得出结论,在能量性能基本持平的情况下,DNAN/HMX(20/80)熔铸炸药的安全及力学性能优于TNT/HMX(25/75)熔铸炸药。     

Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Beam and image experiment of beam deflection electron gun for distributed X-ray sources

Distributed X-ray sources comprise a single vacuum chamber containing multiple X-ray sources that are triggered and emit X-rays at a specific time and location. This process facilitates an application for innovative system concepts in X-ray and computer tomography. This paper proposes a novel electron beam focusing, shaping,and deflection electron gun for distributed X-ray sources.The electron gun uses a dispenser cathode as an electron emitter, a mesh grid to control emission current, and two electrostatic lenses for beam shaping, focusing, and deflection. Novel focusing and deflecting electrodes were designed to increase the number of focal spots in the distributed source. Two identical half-rectangle opening electrodes are controlled by adjusting the potential of the two electrodes to control the electron beam trajectory, and then, multifocal spots are obtained on the anode target. The electron gun can increase the spatial density of the distributed X-ray sources, thereby improving the image quality. The beam experimental results show that the focal spot sizes of the deflected(deflected amplitude 10.5 mm)and non-deflected electron beams at full width at half maximum are 0.80 mm 90.50 mm and 0.55 mm 90.40 mm, respectively(anode voltage 160 kV; beam current 30 mA). The imaging experimental results demonstrate the excellent spatial resolution and time resolution of an imaging system built with the sources, which has an excellent imaging effect on a field-programmable gate array chip and a rotating metal disk.     

Different hydrothermal corrosion results between two sides of sodalime float glass and the possible corrosion mechanism

Sodalime float (SF) glass is widely used in our societies and industries. Hydrothermal corrosion method is one of the effective ways to prepare a superhydrophobic glass, but there is still lack of knowledge about hydrothermal corrosion behavior and mechanism of SF glass. We have hydrothermally treated SF glass at 180 °C for different time, and tried to reveal the aqueous corrosion process of SF glass. We have characterized the morphologies and chemical compositions of samples, and found that (1) the two sides of SF glass have different corrosion resistances, and (2) a multilayer structural coating with a nanoflake layer (Mg-rich gel layer), a nanowire layer (Ca-rich gel layer), and a porous layer (etched layer) is formed on the air-side of SF glass. Based on the experimental results, we have proposed an aqueous corrosion mechanism of SF glass. The insights of the hydrothermal corrosion behaviors and mechanism provide helpful guidelines to glass surface structural control and functionalization.     

Combining molybdenum carbide with ceria overlayers to boost Mo/CeO2 catalyzed ammonia synthesis

The design of an efficient non-noble metal catalyst is of burgeoning interest for ammonia synthesis. Herein, we report a Mo₂C/CeO₂ catalyst that is superior in ammonia synthesis activity. In this catalyst, molybdenum carbide coexisted with the ceria overlayers which is from the ceria support as the strong metal–support interaction. There is a high proportion of low-valent Mo species, as well as high concentration of Ce³⁺ and surface oxygen species. The presence of Mo₂C and CeO₂ overlayers not only leads to enhancement of hydrogen and nitrogen adsorption, but also facilitates the desorption and exchange of adsorbed species with the gaseous reagents. Compared with the Mo/CeO₂ catalyst prepared without carbonization, the Mo₂C/CeO₂ catalyst is more than sevenfold higher in ammonia synthesis rate. This work not only presents an explicit example of designing Mo-based catalyst that is highly efficient for ammonia synthesis by tuning the adsorption and desorption properties of the reactant gases, but opens a perspective for other elements in ammonia synthesis.